A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

在二元柔壁自适应风洞中利用面元法进行三元模型实验

简要叙述了在西北工业大学二元柔壁自适应风洞中利用面元法进行二元半机翼模型试验的研究情况，分析了面元法的基本思想和部分试验结果。     

滑油量对恒速传动装置的影响

本文介绍了中外航空公司飞机发动机恒速传动装置几个故障典例及造成的危害,分析了填加滑油量不当对发动机恒速传动装置的影响,提出了预防措施。     

某无人直升机扩频通信系统捕获方案设计

讨论一种用于某无人机直序扩频通信测控系统的PN码捕获方案。根据该系统的技术指标要求,针对无人机信道的特殊性,采用匹配滤波器进行PN码的相关处理,并运用检测后积分和二次驻留的方法提高检测概率降低虚警概率。在进行详细理论分析的基础上,运用Cadence公司的SPW系统仿真软件,将该系统在高斯白噪信道和无人机信道下进行对比性系统仿真,仿真结果以及FPGA实测结果均表明,上述两种方法有效地提高了系统性能。     

随振动量级增加卫星结构频率下移的分析

对卫星振动频率随量级增加而出现下降，即振动频率“漂移”的现象进行了初步分析。发现随振动量级的增加。结构的非线性表现突出。结构的刚度下降和阻尼增加，可认为主要是由蜂窝材料的非线性因素所致。     

翼板颤振主动抑制的无限维非线性分析

 <正> 1.混合动力学系统的Hopf分叉定理 本文将Marsden-McCracken关于分布参数的Hopf分叉定理推广至混合动力学系统。 设在积空间X=E×R~n中依赖参数μ的演化方程为     

论定常不可压粘流的积分方程解法

本文对定常不可压粘性绕流积分解法中的涡量迭代过程、涡量边界条件的提法以及压强系数的计算等方面都作了改进,使数值解更易于稳定收敛并提高精度。为了验证本文的方法,对低雷诺数下的圆柱绕流进行了计算,结果表明计算效率是高的,迭代过程是稳定的。将本文方法推广到三维流动没有原则上的困难。     

双轴应力下含裂纹加筋曲板剩余强度的弹塑性有限元计算

 采用考虑了大应变的弹塑性有限元方法,以裂纹尖端张开角为断裂准则,实现了双向受载条件下加筋曲板中裂纹起裂到失稳整个扩展过程的数值模拟计算;还对与加筋曲板有同样尺寸的加筋平板进行了分析和计算。结果表明,所提出的分析方法和所采用的断裂准则适用于对含裂纹加筋结构所进行的剩余强度分析。     

尖端具有非线性吸附接触的界面裂纹的动态特性研究

 研究一类尖端具有非线性吸附接触型裂纹模型的弹性波散射问题。利用积分变换和积分方程方法推导了确定这类问题基本变量的奇异积分方程组,采用围道积分技术和切比雪夫多项式展开技术得到了待定系数的非线性代数方程组。最后给出了裂纹尖端接触区的大小和接触应力的数值结果,揭示了这种接触型裂纹模型的动力学特征及物理上的合理性。     

武器系统综合效能的模糊积分评估方法

对系统综合效能的评价是进行系统决策的前提和重要依据,在研制和使用系统时,都要对其进行评价,以便为选择研制方案或使用策略提供支持。指出了概率和统计理论在综合效能评估问题研究中的不足。定义了模糊测度和模糊积分的概念,提出了基于模糊测度和模糊积分的武器系统综合效能评估模型,给出了效能评估的基本过程并进行了应用实例分析研究。